Menu
Your Cart

20-pin split cable / adapter cable for Audi and FIAT 500 (YT-Audi20)

20-pin split cable / adapter cable for Audi and FIAT 500 (YT-Audi20)
20-pin split cable / adapter cable for Audi and FIAT 500 (YT-Audi20)
20-pin split cable / adapter cable for Audi and FIAT 500 (YT-Audi20)
20-pin split cable / adapter cable for Audi and FIAT 500 (YT-Audi20)
20-pin split cable / adapter cable for Audi and FIAT 500 (YT-Audi20)
20-pin split cable / adapter cable for Audi and FIAT 500 (YT-Audi20)
20-pin split cable / adapter cable for Audi and FIAT 500 (YT-Audi20)
20-pin split cable / adapter cable for Audi and FIAT 500 (YT-Audi20)
20-pin split cable / adapter cable for Audi and FIAT 500 (YT-Audi20)
  • Brand: Yatour
  • Model: YT-Audi20
  • Availability: In Stock
  • Delivery time: 1-3 werkdagen
  • Warranty: 2 jaar
€ 8.00
Ex. VAT: € 6.61

A split cable / adapter cable to split the 20-pin block cable that is connected to the back of a number of Audi, Volkswagen and FIAT 500 car radios and navigation systems to enable the installation of an interface.
This makes it possible to use our interfaces (YTM05-VW8, YTM06-VW8 and YTM07-VW8, YT-BTA-VW8, AL-1080A-VW8, AL-1080B-VW8, MN-603-VW8, MN-BUA-VW8) Can be used with, among others, the following car radios and navigation systems:

  • Chorus 1
  • Chorus 2
  • Concert 1
  • Concerto 2
  • Navi Plus 1
  • Navi Plus 2
  • Symphony 1
  • Symphony 2
  • Volkswagen Phaeton Z6Z9

Installation in combination with VW8 cable (Mantson, Yatour and Anycar):

1) Disconnect the black wide 20-pin connector from your car radio.




2) Plug the disconnected black wide 20-pin connector into the red portion of the 20-pin split cable.




3) Take another section of the split cable with the yellow/green/blue section and slide the blue section out of the green connector. To do this, the release pin of the green connector must be pressed.




4) Slide the blue 8-pin connector of the interface cable (A) over the green part of the 20-pin split cable. The blue connector of the split cable does not need to be connected to anything and remains loose.




5) Plug the yellow/green/blue part into the car radio instead of the black wide 20-pin connector that was originally in your car radio.




6) The ground wire (C) of the interface cable must be connected to the back of the housing of your car radio.
Unscrew one of the screws on the back of your car radio.




7) Then tighten the ring of the ground wire properly.




Result:

Installation in combination with VW8D cable (Yatour only):

1) Disconnect the black wide 20-pin connector from your car radio.




2) Plug the disconnected black wide 20-pin connector into the red portion of the 20-pin split cable.




3) Take another section of the split cable with the yellow/green/blue section and slide the blue section out of the green connector. To do this, the release pin of the green connector must be pressed.




4) Plug the blue connector removed in step 3 into the black (female) port (B) of the cable included with Yatour.




5) Slide the blue 8-pin connector of Yatour cable (A) into the green part of the 20-pin split cable.




6) Plug the yellow/green/blue part into the car radio instead of the black wide 20-pin connector that was originally in your car radio.




7) The ground wire (C) of the Yatour cable must be connected to the back of the housing of your car radio.
Unscrew one of the screws on the back of your car radio.




8) Then tighten the ring of the ground wire properly.

Related Products

People Also Bought